...
+1 (786) 206-8151
Licensed & InsuredSame-Day Available

How to Get Rid of Mildew Smell in a Washer — and Keep It From Coming Back

Our certified technicians handle all major household appliances — from refrigerators and washers to ovens, dryers, and dishwashers.

Blog

How to Get Rid of Mildew Smell in a Washer — and Keep It From Coming Back

Appliance repair technician inspecting a front-load washer door gasket for the source of a mildew smell

A mildew smell in a washer usually comes from moisture and residue collecting where a normal wash cycle cannot rinse or dry completely. The fastest safe approach is to clean the accessible gasket or tub rim, detergent dispenser, and user-serviceable pump filter, then run the washer’s designated Tub Clean or Self Clean cycle with one product approved by the manufacturer. Finish by drying the machine and correcting the habit or drain condition that allowed the odor to return.

Never mix chlorine bleach with vinegar, ammonia, acids, or another cleaner. Combining products can release dangerous gas. Use one approved product at a time, follow its label, and check the instructions for your exact washer model.

In this guide: Quick cleaning order · Identify the odor · Front-load steps · Top-load steps · Why it returns · When to request service

The quick, safe cleaning order

  1. Empty the washer. Remove wet laundry and any visible debris.
  2. Disconnect power before hand cleaning. Wipe only areas the owner’s manual identifies as user-accessible.
  3. Clean moisture traps. On a front-loader, inspect the door glass and gasket folds. On a top-loader, inspect the tub rim, lid, dispensers, and accessible surfaces around the wash plate or agitator.
  4. Remove and wash the dispenser if the manual describes it as removable.
  5. Service the pump filter only when applicable. Use the model’s draining procedure and expect retained water.
  6. Run Tub Clean, Self Clean, or the specified maintenance cycle with the product and placement directed by the washer manufacturer.
  7. Ventilate and dry. Wipe remaining moisture and allow airflow when it can be done safely.

This order matters. A cleaning cycle cannot rinse a thick layer of softener from a dispenser or remove a hairpin buried in a gasket fold. Conversely, wiping only the visible door seal may leave residue in the tub, pump path, or dispenser system.

Identify the smell before you clean

What it smells like When it is strongest More likely source First response
Musty, damp, or mildew-like When the door opens or wet clothes are removed Gasket, dispenser, tub residue, filter, retained moisture Follow the cleaning procedure for the washer model
Sour laundry On clothes after a completed cycle Clothes left wet, excess detergent, dirty washer, incomplete rinsing Clean the washer first; rewash clothes according to fabric-care labels
Sulfur, sewer, or rotten-egg odor During drain or near the standpipe Drain-hose installation, siphoning, household drain, stagnant water Check the model’s drain-hose requirements; consider plumbing help
Burning rubber, hot plastic, or electrical odor During agitation, spin, or heating Friction, trapped item, motor/drive or electrical issue Stop the washer and disconnect power if safe; do not treat it as mildew

Odor location is an important clue. Smell the empty, cool drum, the detergent drawer, the gasket, and the air near the standpipe without putting your face into an opening. Note whether the odor appears only while water drains. A washer-cleaning tablet cannot correct a dry household trap, an incorrectly positioned drain hose, or an electrical fault.

Why does a washer start smelling musty?

Moisture stays inside after the cycle

Washers are built to contain water, so several areas remain damp after the visible drum looks empty. The folds of a front-load gasket, the dispenser path, and the pump-filter housing can hold small amounts of water. Closing the door and drawer immediately reduces evaporation and gives odor-producing buildup a better environment.

Too much detergent or fabric softener leaves residue

High-efficiency machines use less water than many older washers. Pouring more detergent than the load, water conditions, and product label require can leave a film rather than produce a cleaner load. Fabric softener can add another coating. Lint, body soil, and hair adhere to that residue, especially in cool, short cycles.

Do not adopt a universal number of tablespoons from a general article. Concentration varies significantly. Use HE detergent when the machine calls for it and measure according to the detergent label and washer manual.

The dispenser, gasket, or filter needs maintenance

A clean-looking stainless drum does not prove the water path is clean. Detergent can gel inside the drawer, hair and lint can remain beneath a gasket fold, and debris can collect in a user-accessible pump filter. LG identifies these areas—along with a Tub Clean cycle—as key odor-maintenance points in its washer odor and buildup guidance.

The washer is not draining as designed

Standing water, slow draining, repeated drain errors, or a filter that quickly fills again suggests more than routine surface cleaning. An unlevel installation can also affect how water and additives move through some machines. A drain hose pushed too far into a standpipe can contribute to siphoning or odor problems, but the permitted insertion depth and routing are model-specific.

Samsung lists drain-hose setup, detergent buildup, retained moisture, load habits, and pump-filter care among its odor checks. Its guidance separates mildew odor from sewer and burning smells, which require different responses. See Samsung’s washer odor troubleshooting.

How to remove mildew smell from a front-load washer

1. Empty and power down the machine

Remove all clothing. If water is standing in the drum or the washer displays a drain error, do not start by adding cleaner. Consult the manual for safe draining or arrange service. Otherwise, switch the washer off and disconnect power before wiping the gasket, drawer, or filter area.

2. Clean the door glass and gasket folds

Gloved hands wiping light residue from the rubber door gasket of a front-load washer

Gently pull back each accessible fold of the rubber seal. Remove lint, hair, coins, and other loose material. Wipe the gasket and the underside of the door glass using the cleaning method specified in the owner’s manual. Rotate the drum by hand only when the machine is disconnected and avoid forcing the gasket away from its retaining hardware.

Dark staining is not always removable surface residue. If the rubber is torn, distorted, leaking, or deeply stained after proper cleaning, have the seal inspected. Do not scrape it with a blade or soak it with an improvised chemical mixture.

3. Wash the detergent dispenser

Gloved hands rinsing and brushing a removable washer detergent dispenser in a utility sink

If the drawer is designed to come out, use its release tab and remove the inserts as the manual shows. Rinse away softened detergent and fabric-softener residue with warm water and a soft brush. Clean the accessible drawer cavity with a damp cloth without flooding it. Dry the parts before reinstalling them.

If the drawer does not release easily, stop. Clips and siphon inserts vary by model, and breaking one can create dispensing or leakage problems.

4. Clean the user-accessible pump filter

Gloved hands opening a front-load washer pump filter with towels and a shallow tray positioned for retained water

Not every washer has an owner-serviceable filter. Check the manual before opening anything. If yours does, place towels and a shallow container below the access door. Use the emergency drain hose first when the procedure includes one, then loosen the filter slowly. Water can remain even when the drum looks empty.

Remove accessible lint and objects, rinse the filter, inspect its sealing surface, and reinstall it exactly as directed. A cross-threaded or loosely installed cap can leak. Our guide on where to find a washing-machine filter explains why filter location and maintenance differ among models.

5. Run the designated cleaning cycle

Restore power after all hand-cleaned components are correctly installed. Keep the drum empty. Select Tub Clean, Self Clean, Clean Washer, or the maintenance cycle named in the manual. Use one approved cleaner in the specified compartment or drum location. Do not assume that a normal hot wash is equivalent to the dedicated program.

LG’s current tub-clean guidance recommends cleaning the gasket, dispenser, drain-pump filter, and other listed maintenance points along with the cleaning cycle. It also advises following the package directions for washer cleaner and ventilating the washer afterward. See LG’s front- and top-load Tub Clean instructions.

6. Dry before closing

When the cycle finishes, wipe the door glass, gasket, and visible drum moisture. Allow the drum and dispenser to air out when household safety permits. A door left wide open can create a hazard for children or pets; use the manufacturer’s recommended ventilation position and supervise the area.

How to remove mildew smell from a top-load washer

A top-loader does not have the same door boot as a front-loader, so gasket-focused advice misses common odor areas. Disconnect power for hand cleaning, then inspect:

  • The underside of the lid and the upper tub ring.
  • Detergent, bleach, and fabric-softener dispensers.
  • Accessible surfaces of the agitator or wash plate.
  • The basket holes and areas where lint or product residue is visible.
  • A user-serviceable lint or pump filter only if the manual identifies one.

Clean removable dispenser parts in a sink and wipe accessible stationary surfaces. Do not pull off an agitator cap, wash plate, or tub ring merely because an online video shows a similar-looking washer. Fasteners, seals, and removal procedures differ, and some components are not intended for routine owner removal.

Reassemble the removable user-maintenance parts, leave the basket empty, and run the specified cleaning cycle with one approved product. Wipe and dry afterward. If flakes or odor return repeatedly, an internal buildup, drainage condition, or component that requires disassembly may need professional attention.

Which cleaner should you use?

The right answer is the product class permitted by the washer manufacturer—not the strongest recipe found online.

  • Commercial washer cleaner: often the simplest option when its label and the washer instructions agree. Put tablets, powder, or liquid only where directed.
  • Chlorine bleach: some manufacturers prescribe it for a specific mold procedure or cycle; others restrict its location or amount. Never improvise the dose.
  • Oxygen-based cleaner: recommended for some machines and gaskets. Confirm compatibility with the model and product label.
  • Vinegar: mentioned in some manufacturer guidance but not universally approved for every seal, hose, dispenser, or cycle. Do not treat it as automatically safe for every washer.
  • Baking soda: not a substitute for removing residue from a gasket, drawer, or filter. Mixing it with vinegar largely neutralizes the acid-base reaction and is not a universal washer-cleaning protocol.
Critical safety rule: never combine bleach with vinegar, ammonia, toilet cleaner, rust remover, descaler, or another cleaning product. If an unknown product is already in the washer, rinse according to its label and ventilate before using anything else. If irritating fumes develop, leave the area and contact emergency or poison-control services as appropriate.

A fresh smell does not prove a washer is clean. Fragrance can cover an odor temporarily while residue remains. The goal is to remove the material holding moisture and then correct the cause.

Why does the mildew smell come back?

The visible area was cleaned, but the water path was not

Wiping the gasket may produce an immediate improvement while the dispenser, filter, or outer-tub surfaces remain dirty. Clean all owner-accessible maintenance points listed for the model and complete the designated cycle.

Detergent habits have not changed

If each load adds another layer of detergent or softener, the smell can return quickly. Check whether the detergent is HE-compatible, measure rather than pouring by eye, and adjust within the manufacturer’s directions for load size and product concentration.

The washer cannot dry

Promptly remove laundry, wipe moisture traps, and provide safe airflow. This matters even more in a warm, humid laundry area. Do not store damp towels or workout clothing inside the washer between loads.

Water is not leaving completely

A clogged accessible filter, kinked hose, drain-pump issue, or installation problem can leave stale water in the system. If the washer drains slowly, leaves clothes unusually wet, shows an error code, or has standing water, diagnose the drainage problem rather than running repeated cleaning cycles.

The odor is coming from the household drain

A sewer odor concentrated near the standpipe or appearing only during drain may originate outside the washer. Check the installation diagram for hose height, air gap, insertion depth, and required securing method. Do not seal the hose into the standpipe unless the plumbing and appliance instructions require a specific fitting; the drainage system normally needs proper venting and an air path.

How to keep the washer from smelling again

  • Remove laundry soon after the cycle ends.
  • Wipe the door glass and gasket or the lid/tub rim when moisture remains.
  • Let the drum and dispenser dry with safe ventilation.
  • Use the correct detergent type and measured amount.
  • Limit fabric softener to the washer and product instructions.
  • Run the manufacturer’s maintenance cycle at the recommended interval.
  • Clean removable dispenser parts and an applicable pump filter periodically.
  • Respond to slow draining, leaks, and error codes instead of masking odor with fragrance.

Manufacturer intervals differ. Some machines display a cleaning reminder based on cycle count, while others specify a monthly routine. Follow the manual rather than resetting or ignoring the reminder.

When cleaning is not enough

Request diagnosis when the odor remains after the complete model-approved procedure or when you find:

  • Standing water or repeated drain errors.
  • A pump filter that cannot be removed, sealed, or cleaned safely.
  • A torn, leaking, or distorted door gasket.
  • Recurring black residue or flakes after proper maintenance.
  • A sewer odor linked to an installation or drain condition you cannot verify.
  • A burning-rubber, hot-plastic, or electrical odor.
  • Leaks, abnormal noise, or a drum that does not operate normally.

If your washer also becomes loud at high speed, use our guide to a washer making noise during the spin cycle to separate load and installation issues from mechanical symptoms.

For service in our coverage area, visit our washer repair page. You can review current service-call and diagnostic pricing and contact Oleg Appliance Repair with the model number, odor description, any error code, and the cleaning steps already completed.

Frequently asked questions

Can I use vinegar to clean a washing machine?

Only when the washer manufacturer and the vinegar product instructions permit it for that model and procedure. Vinegar is acidic and is not a universal choice for every seal, hose, or cycle. Never combine it with chlorine bleach.

Can I use bleach to remove mold from a washer?

Some manufacturers provide a bleach procedure for visible mold or a mildew odor, including a specific compartment, quantity, and follow-up rinse. Other machines or components may have different restrictions. Use bleach only as directed for the exact model, keep the drum empty, and never mix it with another cleaner.

Why do clean clothes still smell musty?

The washer may be transferring odor from residue, clothes may have remained wet too long, too much detergent may have prevented complete rinsing, or the household water/drain system may be involved. Clean the machine before repeatedly rewashing, then follow the fabric-care label for the affected clothing.

Why does my washer smell like sewage when it drains?

The smell may be related to the drain hose, standpipe, trap, venting, or water siphoning back toward the washer. It is different from ordinary gasket mildew. Compare the installation with the model manual and involve a qualified appliance technician or plumber depending on where the fault lies.

How often should I run Tub Clean?

Use the interval in the owner’s manual or the washer’s cleaning reminder. A common monthly pattern appears in manufacturer guidance, but the model’s cycle count and instructions take precedence. A persistent existing odor may require the manufacturer’s short-term repeated-cleaning procedure rather than an indefinite weekly routine.

Do front-load washers smell more than top-load washers?

Front-load designs have a watertight door gasket that can retain moisture and debris, making gasket care especially important. Top-load machines can still develop odor in dispensers, the tub ring, wash plate or agitator area, and drain system. Maintenance habits and detergent use matter for both designs.

When should the washer door gasket be replaced?

A gasket may need replacement when it is torn, leaking, deformed, no longer sealing, or has contamination that cannot be safely removed using the manufacturer’s procedure. Staining alone is not enough to diagnose failure. Have the part inspected before ordering a replacement.

Categories

(786) 206-8151

Book Online

(786) 206-8151

Book Onlin

(786) 206-8151

Book Online

(786) 206-8151 WhatsApp

Insured businessCommercial General Liability coverage active through November 4, 2027. View insurance certificate